Posts by amiga1260
Caution: Non registered users only see threads and messages in the currently selected language, which is determined by their browser. Please create an account and log in to see all content by default. This is a limitation of the forum software.
Also users that are not logged in can not create new threads. This is a, unfortunately needed, counter measure against spam. Please create an account and log in to start new threads.
-
-
Okay, I solved my problem by puttting the Inidiswitcher after the c:LoadMonDrvs in the Coffin Startup-sequence. Now it works.
-
I have a Vampire V2 600 and I want to use Indiswitcher with my Indvision ECX V2 to switch between VGA and HDMI(Vampire Output).
I installed the latest version 3.3.2 of P96, but I still get the errorIndiswitcher needs rtg.library 41, but RTG.library 43.3 is installed.
I already uninstgalled Picasso 86 and reinstall the Saga driver of the Vampire. What do I wrong and were can I get he RTG.library V41.
-
-
-
It works great my favorite A1200 Demo finally wors without snow.
-
Thank you for your answer.
-
Is it possible to send ACA1234 in for optional Wire link?
I already have the CPLD V3 and the latest firmware installed.
I live in the Netherlands.
-
I checked for bent pins and I also tried it on another ACA 500 Plus version befor 2018 with v0.140 and that one also has no bent pins.
I also checked it wit honother Amiga 500 rev 6 and the issue is stil exists.
After setting the jumper JP0: to "safe launch @25MHz and EEPROM settings reset" and turning on the Amiga 500 and the Cf Aux and Boot disk slots of the ACA 500 Plus work again.
After that I set the jumper back to factory setting and now all the CF cards will show in Workbench.
I have solved my own problem.
-
Today I update the firmware of my ACA 500 Plus (After 2018) from 0.135 to 0.140 and I also update the ACA 1234 CPLD.
After these update I can't boot from the Aux card and Boot card of ACA 500 plus.
The boot card doesn't show up in the Early startup.
My configuration is:
Amiga 500 REV6 modded to 1 MB chip
CA-PSU
ACA 500 Plus After 2018 model
Sandisk 4 GB CF card in boot card slot ACA 500
Sandisk 32 GB CF card in ACA 1234f
I also tried to flash to go back to 0.135.
-
-
Yesterday I got my ACA1234. I want to know how I can activate AmiTCP and PCMCIA Network driver?
IS there a possiblity to use an ACATool to turn ooff th ACA1234?
-
Thank you for replacing the Indivision and it works perfectly.
-
Thank you. I will read your topic before sending to you.
-
Today I was using my Indivision AGA MK3 on my Amiga 1200 and suddenly I get the artifacts in the screen.
My Amiga 1200 has a Blizzard 1230IV and a REV1D4 Motherboard. The PSU I tested are an A500 Light PSU 4.5A and The CA-PSU.
I also swapped the Indivision AGA MK3 with other Indivision AGA MK3.
After swapping I didn't have this issue. I also tried the artifacted Indivision AGA MK3 in the other Amiga 1200 with a REV2B Board and A GVP 1230 II.
It also gives artifacts.
I also tried two monitors ands cables. Both Amiga 1200 has been recapped. I thik I need to send it to repair.
-
I tested the new firmware 1.8 with some games like Turrican 1,2,3, Apydia, Rick Dangerous 1 and 2 WHDLoad versions and I get background music and sound effects. I think the audio problems are solved.
Thank you Jens.
-
Did you already solved my issue?
-
I found some games (Turricon series and Apydia) from Factor 5 which don't output sound through HDMI. I'm using a Iilyama ProLiteXB2380HS.
monitor. Could you try to fix it if it's possible?
-
I didn't use the ACATool. It doesn't crash when I copy files from HD to RAM disk without inserting PCMCIA CF card reader.
When I do the same task with the PCMCIA CF card reader, then it crashes and I get a Gurru Mediation Error 0100 00C.
When I look up the error messsage on http://www.lemonamiga.com/forum/viewtopic.php?t=13978. The error is that it couldn't get the avail memory.
-
I'm using a Sandisk PCMCIA card with a Sandisk 8 GB CF and using Kickstart 3.1 on both Amiga 1200.
It only crash when I trying unpacking files in Ramdisk.