Caution: Non registered users only see threads and messages in the currently selected language, which is determined by their browser. Please create an account and log in to see all content by default. This is a limitation of the forum software.
Also users that are not logged in can not create new threads. This is a, unfortunately needed, counter measure against spam. Please create an account and log in to start new threads.
Don't Panic. Please wash hands.
-
LAST UPDATE
Hi Jens !
I could not sleep last night
I tested all the motherboard of my computer and I found some problems with some damaged welds
I have redone the welds and now the interface works
But I can not use my old interface for CF
With this IDE / CF interface it no longer works
I installed a normal rotary IDE disk and i formatted with sucess and now the system works
I will continue to check my computer
Thank you so much for your patience and for your advice
BYE JENS !!!!
-
I'm sorry
I thought that the laboratory was located in another address
I prepare the package
thanks again for your time
Bye jens
-
ok Jens
please you can write me address ?
thanks for your help jens !!!
-
Please write in English here - I don't speak Italian, and I also don't like to use automatic translation, as I just don't trust it to be accurate.
sorry
Yes same issue
-
Stesso problema anche in uno slot diverso? In tal caso, impacchettalo insieme al DOM e daremo un'occhiata qui.
sì
stesso problema
-
Jens .... sale issue
I think I'm unlucky
drive name = DIWR intead of Disk ......
-
"Diwk" instead of "Disk", that shows a false bit, possibly because of a bad connection (it does not seem to be the resistor of shame). Try taking out the controller, clean the connector with alcohol and an old toothbrush and try that again.
OK
I try now
-
3° test = insert dom and CF/IDE
I performed the same steps as above, but on both units and you put only the pictures of the final result
in any case, if you reboot, no disk to format is shown
-
2° test = only IDE/CF ( no DOOM insert )
the system sees no disc inserted
-
Sure
1° test = DOM
I show in the picture throughout the procedure that I do for the DOM unit
I will then reboot and I should see the drive to be formatted
however do not see the drive to format and the procedure it is as if it had never been done
-
OK
the card is always displayed in the diagnostic, and it is in the working state
When I try to get a HardDisk IDE or CF to read, with an IDE adapter, it always gives me zero space
I noticed that with the DOM inserted in port one the buddhascsi.device device is present
but if I remove the DOM from port 1 it is no longer present (I use SYSINFO to see the DEVICE)
I tried to hold down the two mouse buttons and see in the BOOT menu if it presents me with some disk but I only see DF1 and DF0
ROM UPDATE
IN boot menu Found only DF0 and DF1
Diagnostic Menu
In HDtool I found 2 unknown device
I try read the HD IDE or CF IDE same result ... zero
-
Jens
now no longer sees any disc
I think it's broken
is it possible to send it to you for repair?
-
OK
I use command FORCE/S and now, I was successful
I try now format HD
-
- Buddhaflashtool Buddha_ROM_52-101.bin
I apologize ...
I use the above command
is not that correct?
-
Sorry Jens
I followed the instructions for making updates
I hold down the right mouse button in the boot computers (nothing happens) then I insert the floppy workbench with the program, and ROM
Type the command but when it asks me to press the Y button, nothing happens and remains as in the picture
where am I doing wrong?
-
I had done a check on the computer power supply but some time ago
the new control and verify all voltages
I think this may be the real problem.
I have another power supply, to which I have recently changed all the capacitors
I will use this power supply with the new capacitors
thanks again !
-
I have not done anything special, but I have not used the computer for a few months
perhaps the CF that I'm using is not of good quality
I will try to follow the instructions to flash the ROM
Thanks a lot JENS !!!
-
can anyone help me?
the situation is so desperate?
I have to throw away my card?
-
sorry for my bad english
the day 12 apr 2019 I purchased the Buddha interface and there have been no problems to date
I can not more to start my HD that are all called as a DF4 and DF5, or DF 6 etc.
it ruined my CF with the data inside them
I tried to format everything again
but I can never format and the computer freezes when it's formatting
what can I do ?
is it possible that it is already broken without me doing anything?
please help me
Igor
I attach images