Caution: Non registered users only see threads and messages in the currently selected language, which is determined by their browser. Please create an account and log in to see all content by default. This is a limitation of the forum software.
Also users that are not logged in can not create new threads. This is a, unfortunately needed, counter measure against spam. Please create an account and log in to start new threads.
Don't Panic. Please wash hands.
-
The image from the converter certainly isnt as sharp as the MK3, and there is some flickering with interlacing modes, but the test patterns are readable and I don't get the same noise/distribution as shown in the picture. I also don't see the same noise/distortion with an OSSC or from the one monitor I was able to get working directly from the A1200.
I haven't had an the opportunity to bring the configuration app over to the Amiga so I'll do that shortly and see how that works.
-
With the the MK III installed Im getting noise/distortion in high resolution modes. See attached picture. I do not have the noise issue at those resolutions without the card. (Standard Amiga output to SCART to HDMI converter)
I've clean the Lisa pins, reseated the card, tried different monitors and cables, with and without the ACA1233n accelerator, and with different power supplies.
One suggested solution was to jumper E127R.
My configuration:
A1200 Channel Z Rev 1D.3
ACA1233n accelerator
Commodore PSM‐600 & Keelog power Supply
64 Gig Compact Flash HD and adapter
Hardware Gayle reset fix
-
Sorry, just courious, but It looks like the accelerator got delivered a couple weeks ago and I was wondering if you'd had a chance to look at it yet?
Thanks
-John-
-
I wanted to wait for the new ACA1233N-55 to arrived before I sent off the bad Accelerator, It arrived the other day, I installed it, it boots right up, so the A1200 looks good!
I'm going to ship the bad accelerator shortly, and just want to confirm the address will be the same as the return address on the recent package and the About Page on icomp.de.
Thanks!
-
I'm in the US and the PSU natively rated at 117 VAC.
As it would add size and weight to the parcel, the added shipping cost during the Pandemic is rather prohibitive, and I've had a significant number of international shipments seriously delayed or outright lost in transit, I'd rather not send the PSU right now.
If there isn't a rush, I purchased an ACA1233N‐55 from you yesterday, and its been shipped, so once the new accelerator gets here, if it's happy with the other 4.5A CBM PSU, I will check on the current shipping costs and if I can get it insurance and priority shipping, I'll consider sending it back with the ACA1233N-40 if you think that's helpful.
-
Channel Z A1200 Rev 1D3
Commodore PSM-600 power supply
Gayle reset
3.1.4 ROM
64Gb CF on a Rastport right angle adapter
Tom+ USB mouse adapter
I have tried a different CBM power supply, cleaned the connectors, and tried pulling the card down .5mm or so to touch a different part of contacts.
-
My A1200 and ACA1233n were working, now it won't boot with the accelerator installed. Have tried reseating the card but nothing helps
-
Hi, I bought a Rapid Roads about a year ago from Amigakit and just got around to installing it in an A1200 and It doesn't seem to be working. I've checked the cabling, no USB devices are being recognized, the LED doesn't come on, the ports don't appear to be getting any power, and it's getting about finger burning hot. Would it be possible to have it serviced?
-
I recently purchased an ACA1233N and read in the icomp wiki page for the card of the timing issues. While the new card can compensate for the timing issues, it recommended that the problem capacitors still be remove. Does this mean, along with E123C and E125C, that E121C and E122C should be removed as well?
-John E. Bielak-