Phil pls share your config files. Thx
Posts by BlackTiger78
Caution: Non registered users only see threads and messages in the currently selected language, which is determined by their browser. Please create an account and log in to see all content by default. This is a limitation of the forum software.
Also users that are not logged in can not create new threads. This is a, unfortunately needed, counter measure against spam. Please create an account and log in to start new threads.
Don't Panic. Please wash hands.
-
-
Hi
Noctua NF-A4x10 FLX have to models 5v and 12V with one you used ?
-
Hi Jens will you offer any mounting set for this case
like this ? https://shop.pixelwizard.eu/en…-case?number=SW10055&c=35
will there be any updates for Ultimate 64 Eite users in this reworked cases ?
Is your Commodore 12V PSU compatible with U64 boards ?
Thx for info
-
few test
1. config tool 16 + firmware 16 - OK no requester, options save, full screen bug
2. config tool 16 + firmware 171 - OK no requester, scanlines save problem, but its OK, full screen bug
3. config tool 17 + firmware 171 - requester on every start, scanlines save problem, full screen bug
(in 2 and 3) manual save is big help here
full screen bug - I mean sometimes after powering off display returns do default not scaled position
for the time being i choose 2.
will test more later
Timm: whats your opinion on interlace in pinball illusion on movie i uploaded ? I dont know how i suposed to be not playing interlace just observation.
Another issue is Graffiti demos works, but Nemac and shapeshifter dont some time ago a spoke to Jens but nothing new in this case, maybe you will help
-
no Cosmos-patch or MCP
thx guys for your time and commitment
-
BlackTiger78 : With your accelerator and the PSU being known-good, we have to assume that some software is causing the malfunction. Can you please list the system patches that you have installed?
I got your CA-PSU + ACA1233
Its plain OS3.1, MUI, MagicWB, some tools and stuff
if there is something dony know much about patches, tell me what i will se
without startup-sequence got info 0 VGA modes then reset do default and got 2 vga modes added
also got the same requester but notice that may be is some cases a "visual glitch" or something because for test i enabled Graffiti, saved, rebooted, run it again got requester BUT grafiti stays enabled
-
no EDID modes on mk3tool
floopy adf and plain files atached
-
Thanks, but I'd need a listing using the 'list' command to see the protection bits, too.
also notice strange behavior in interlace in pinball Illusion i dont know is it wrong its nice in one direction, wrong in another, siwtching options in indi can revers the process
https://www.youtube.com/watch?v=dE6V2csWA04
saving issue i previously wrote
-
I made two another 171 rescue disks, same error, disks validated no error, manual replacing files fixes problem
got idea maybe I will upload files in arch from fresh rescuedisk to compare, maybe this will help, let me know
my configuration file atached
-
I cannot reproduce issues with creation of a rescue disk. I tested it several times.
i will make few more rescuedisk later see what happend
I can however confirm a bug with saving the scanline setting. The scanline setting is canceled out from the configuration on the device.
i also have bug with saving configuration to device on 171 each startup got info
"The configuration is not saved to the device" i must do flashtool saveconfig config
Regarding your monitor, if possible, please read and save the monitor EDID using the command line:
# IndivisionAGAmk3 SAVEEDID myedid
and post the file myedid here.
many times screen goes black and got info Could not read EDID, very few read success
-
sorry for double post can't edit first
- got strange white screen error, reset doesn't help, resue disk did - it happend after live mode changes
it stays on screen even when reset amiga or powers off
- still cant read any info from monitor 27" Acer XB271HU maybe to modern, conected via hdmi
- everytime I started IndiMK3 gof got prompt configuration is not saved to device,
(I edit, save (sometimes saves act as Redo) when started again, same prompt again. - 171 only
are old saved configuration compatible with new version ?
-
worst:
- i thing there is a "copy error" with creating rescue disk in 1.7.1
tested 3 times good diskietes and after boot got this error flashtool - file is not executable
after manual copy files from IndiMk3 dir all works fine.
- another problem 171 dont always save a configuration to device (scalines for examples) - 16 all ok
better:
- yellow vertical line at the far right of the screen - fixed
-
After few days of test have a big problem now, MK3 stoped working after reset.
Screen starts flashing lines and wb bars on botom after reset Hardware not found,
A1200 work signal on rgb out.
I let her rest no changes, removed and instaled MK3 again no changes,
when i want to load the Config Tool from the provided ADF 1.4 it shows
first "couldn't open asl.library" and then second "IndivisionAGAmk3 Hardware not found"
then suspend/reboot
and my recovery disc got bad sectors
Is booting 1.4 adf without ss and
flashtool flash firmware
will help ?
Update: DONE flash do its work
But what caused the crash ?
-
So about Graffiti was i was able to check
- viever ok will test more
- tech demos (from your link) - ok
- Nemac IV - errors, wrong colours see prev screens, tested 2 versions
its black and white sometimes green and blue (dont know its important) look at atached OSD resolution
- Shapeshifter - on Graffiti 030MMU got errors with overscan see 2.jpg when set overscan Curent Position: (8,8) got this error 4.jpg
(shapeshifter works fine without selected graffiti mode)
About MK3:
1. I can't read monitor (Could not read Display Information) data from my 27" Acer XB271HU (via HDMI)
2. can read on NEC 20WGX2 (via HDMI-DVI)
checked 3 cables all works, same cables works with MK2cr
3. Sometimes in few games and when workbench starts I have vertical yelow line always on right side see 3.jpg
4. CIA adapter is too close to keyboard connector cant disconect kb without removing CIA
Amiga 1200 ,ACA1233 MMU 40MHz, Your PSU, CF 4GB,
-
im not sure what you mean
This is my settings Curent Position:(8,8), Current size 664x264
if not that point my on right place
-
ovescan settings 720x277 if that what you mean same results
-
viever and demos to works fine, Nemac still have problems
-
Please note that this is a "per screenmode"-setting. If you have enabled it for your WB mode (which may be "on SHires only" or even HighGFX), then it's not automatically enabled for PAL or NTSC.
on wb i have pal hires, i tried to start without startup-sequence same result
-
no no my mistate no gloom, nemac iv, dont have c2p for gloom still searching
-
sorry nemac IV , graffiti enabled in mk3 settings