My MK3 1200 is not working at all. I just bought it. I am sure it is connected properly. Machine boots up normally with composite cable but VGA and HDMI Do not work at all.
Can you please help me?
Caution: Non registered users only see threads and messages in the currently selected language, which is determined by their browser. Please create an account and log in to see all content by default. This is a limitation of the forum software.
Also users that are not logged in can not create new threads. This is a, unfortunately needed, counter measure against spam. Please create an account and log in to start new threads.
My MK3 1200 is not working at all. I just bought it. I am sure it is connected properly. Machine boots up normally with composite cable but VGA and HDMI Do not work at all.
Can you please help me?
Let's check the simple things first: You say that you believe it's connected properly. Is the unit really tight on the board so that you can lift the main board on it? Many people don't dare to push as hard as required.
Yes it is completely tight against the board. i am sure it is completely seated.
What's the warranty ID and where on the planet are you?
NT&JE
Ottawa, IL USA
Hi, I'm having the same issue with mine - no output at all on the VGA or HDMI, and it's definitely on there as tight as it'll get. Still got output via RGB, but the card seems kaput
Warranty rT&&N in the UK
In case it's of any use - attempting to use the AGA config tools via the RGB output gives a "Hardware not found" message
We do test each and every unit before it's packed, so the best guess I have is that something mecahnical got damaged. We've changed the way that the units are packed, because there were two cases (both solved here in this forum) where a component was ripped off, likely because something scratched on the surface of the flicker fixer.
I looked up both of your warranty IDs; The one in the UK is on the edge where we've made the change in packing, so it may have come with "all boards in the small bag", but the one from daver999999999 went through QC on August 13th, so it is definitely possible for that to have been damaged in transport. Sorry for being vague about the unit from samingrams - I have access to the QC pictures on the NAS, but the database server is switched off during the weekend.
Please give this a good optical inspection - you're looking for a tiny component that might be ripped off, likely labelled "Ln" with n being a one- or two-digit number. These components are on both sides of the board. If you can take a high-resolution macro picture, I can check that if you post it here.
Hi,
I've had a good look over it, but can't find anything that looks like it's come off. Please see attached pictures.
In case it's helpful as well - I'm running KS 3.1.4 on board Rev1D.1.
[please upload, don't link to data mining pages]
I looked over the board. I don't see anything. I used a Soldering Microscope that I have some pics I took with my phone. The system will not allow me to upload them It says they are too big.
I'm having the same problem. I can't get it to work. It's as firmly installed as I can get it to sit. I cannot find any damage on my Amiga 1200 chips or the Indivision AGA MK3. I connected using RGB to see the screen and booted up the IndivisionAGAmk3-1.6.adf. The message I get is that the MK3 was not detected. Jens, can you help me?
I could not see the dropbox picture, as it would not release any data unless I switch off all safety measures here. Please upload pictures in this forum only.
I'm having the same problem.
Then I have the same request for you: Please report your warranty ID, take high-resolution macro pictures of both sides of the board and post them here (not on some data-mining unrelated page).
The system will not allow me to upload them It says they are too big.
Then downsize them to a level where the amount of data is in proper repation to the visible size It's not all that hard. GIMP on Linux or Irfanview on Windows machines can do it. I'm sure that fruity-glossy computer-like things have similar programs.
So you are saying I need to edit the photographs so I can upload them? So I need to learn to use photo editing software in order to get a warranty replacement? The Board doesn't work. I would like it replaced. Is that not good enough?
right, both these units show no damage at all. I therefore believe that they are still in the state that they left here, and that's "tested, working OK".
Please give your Lisa chip a good wash with an old toothbrush and IPA. While it's still wet, please push the flicker fixer on and see if it's working better. The best explanation I currently have is that the pins of Lisa are oxidized, and at least one essential signal is not making it's way to our logic.
I cleaned with IPA and Deoxit. I saw no Oxidation on any of the pins before or after cleaning. There is still no signal to the HDMI. Attached are the pictures of my Lisa.
The last reply was more than 365 days ago, this thread is most likely obsolete. It is recommended to create a new thread instead.